|
地 址：四川省成都市金牛区金牛坝路4号
电 话：028-87650758
传 真：028-87657508
邮 箱：wswsa@163.com
网 址：Http://www.chinawswy.com
邮 码：610036 |
|
|
|
|
| 标签:联轴器 时间: 2013-12-27 点击: 1236 次 |
|
| 1、请依照马达的种类、用途及使用环境，选择最合适的联轴器。决定联轴器型式后，请依照资料所载的尺寸、规格表决定孔径大小的组合及规格。
◆搭配伺服电机使用时
伺服电机能在高速区域时传达高扭矩，适于高速、高精度的定位。可选择G8L、G8S、G7L、G7S、G6C、G6T、G6E、G5C、G5E、G3C、G3CM，也可以根据伺服电机的额定功率、额定扭矩大小来选择。各联轴器产品的规格请参照资料所载页码，伺服电机详细资料请查阅各电机制造商相关型录。以上为非搭配减速机使用时，所推荐的联轴器型式。
◆搭配步进电机使用时
步进马达能在低速区域时传达高扭矩，适用于高精度的定位。可选择G1T、G2T、G2C、G3T、G3C、G6T、G6C系列联轴器。
◆搭配普通电机使用时
可选择G6T、G6C、G4T、G4C、G9C系列联轴器。
◆搭配编码器使用时
可选择G1T、T1TM、G3TM、G3CM、G5T系列微型弹性联轴器。
◆特殊工作环境下使用时
耐腐蚀环境下可选择G1TS、T2TS、G2CS、G3TS、G3CS、G5CS等不锈钢材质的联轴器，高温环境可选择采用耐高温度材料制成的滑块联轴器G4T、G4C。
2、选用时请注意资料上的额定扭矩必须大于系统负荷扭矩，额定扭矩已考虑运转时变动负荷因素，所以选定时不必再调整额定扭矩值。选择联轴器的尺寸时，请注意连续运转发生的负荷扭矩要低于额定扭矩。
3、请确认设计的孔径、回转速条件不能超过资料上的最大孔径、最高回转速。最大孔径或最高回转速任一无法满足设计条件时，请变更尺寸。
4、最后请确认尺寸、规格表等其它数值是否也符合设计的相关条件。
详细数据请登陆我司网站，网址：www.chinawswy.com 欢迎新老客户来电咨询、洽谈。
1, please according to the types of motor, USES and the use environment, select the most appropriate coupling. Decision after coupling type, please according to the information contained in the size, specification table determine the combination of the aperture size and specifications.
When used in pieces with servo motor
Servo motor can regional ShiChuanDa high torque at high speed, suitable for high speed and high precision positioning. Can choose G8L, G8S, G7L, G7S, G6C, G6T, G6E, G5C, G5E, G3C, G3CM, can also according to the size of the rated power, rated torque servo motor to choose. The coupling of the specifications of the products, please refer to information contained in the page number, detailed information, please refer to the motor servo motor manufacturer catalogue. Above is a tie-in reducer, when using the recommended coupling model.
In pieces when used with stepper motor
Stepper motor can ShiChuanDa high torque at low speed area, suitable for high precision positioning. Can choose G1T, G2T, G2C, G3T, G3C, G6T, G6C series coupling.
In pieces with ordinary motor when using
Can choose G6T, G6C, G4T, G4C, G9C series coupling.
In pieces to match the encoder when using
Can choose G1T, T1TM, G3TM, G3CM, G5T series micro elastic coupling.
When using pieces of special working environment
Can choose G1TS corrosion environment, T2TS, G2CS, G3TS, G3CS, G5CS stainless steel coupling, high temperatures may choose to use high temperature resistant material made of oldham coupling G4T, G4C.
2, selection, please pay attention to the information on the rated torque must be greater than the system load torque, the rated torque has considered varying load factors during operation, so don't need to adjust the rated torque values when selected. When selecting the size of the coupling, please pay attention to the continuous operation of the load torque is lower than the rated torque.
3, please make sure the design of the aperture, and back to speed conditions cannot be more than data maximum aperture, back to the highest speed. Maximum aperture or any failing to meet the design conditions, back to the highest speed change size, please.
4, finally, please confirm whether the size, specification and other numerical also comply with the design of the relevant conditions.
Details please visit our website, website: www.chinawswy.com welcome new and old customers to inquire, negotiate. |
【关闭本页】【打印本页】 |
|
|
|
上一篇：